Series 5 Environmental & Power
This page describes the environmental ratings and power specifications for Series 5 players: LS5 (LS425, LS445), HD5 (HD225, HD1025), XD5 (XD235, XD1035), XT5 (XT245, XT1145, XT2145), and XC5 (XC2055, XC4055).
Environmental
Player Family | Sustained Operating Temp | Transient Temp | Non-Operational Temp |
|---|---|---|---|
LS5 | 0°C to 50°C | Up to 50°C | -20°C to 85°C |
HD5 | 0°C to 50°C | Up to 60°C | -20°C to 85°C |
XD5 | 0°C to 50°C | Up to 60°C | -20°C to 85°C |
XT5 | -10°C to 50°C | Up to 70°C | -20°C to 85°C |
XC5 | 0°C to 40°C | Up to 50°C | -20°C to 85°C |
All ratings are at 90% maximum relative humidity, non-condensing.
Operating the players above their maximum sustained operating temperature (50°C, or 40°C for XC5) for prolonged periods may reduce the operational life of the product and result in intermittent resetting of the device.
Exposing a cold player to warm air at high relative humidity may cause water to condense inside the player, leading to component failure. Damage due to such internal condensation is not covered by warranty. If a player is cold, allow several hours for it to acclimatize to ambient conditions before applying power.
Power
Power Adapter
Player Family | Supplied Power Adapter |
|---|---|
LS5 | 12V @ 1.5A |
HD5 | 12V @ 3A |
XD5 | 12V @ 3A |
XT5 | 12V @ 3A (36W) |
XC5 | 19V @ 4.7A (90W) |
The XT5 uses approximately 12W (1A) of power when playing a 4096x2160x60p H.265 (HEVC) source file.
The XC5 uses approximately 18W when playing a 3840x2160x60p H.265 (HEVC) source file, and approximately 27W when playing a 7680x4320x60p (8K) H.265 (HEVC) source file.
Peripheral Power Budget (XD5 and XT5)
When powered by the power adapter, XD5 and XT5 players have an additional 2A (24W) of power available to be shared between connected peripherals. Do not connect any combination of peripherals that will exceed this budget. If more than 2A (24W) is drawn, the external power supply may shut down due to over-current conditions. The unit will not be damaged, but it may reboot or not operate properly until the overload is removed.
On XD5 players, the 2A can be shared in any way among the following connectors:
Connector | Maximum Power Usage |
|---|---|
RJ-45 | Approx. 180mA (when transferring data) |
USB 2.0 (Type C) | 1A |
USB 2.0 (Type A) | 1.5A |
GPIO 3.3V | 500mA |
HDMI® 5V | 70mA |
IR blaster output | 85mA |
M.2 Wi-Fi Module, M.2 SSD Module | 3V3 – The combined power of these expansion ports should not exceed 3.5A |
Peripheral Power (XC5)
On XC5 players, 3.3V power is available on the M.2 expansion ports for peripherals (Wi-Fi module and SSD module). Power to each port is not restricted, but the combined power draw of the M.2 ports should not exceed 3.5A. If more than 3.5A is drawn, the power supply may shut down due to over-current conditions. The unit will not be damaged, but it may reboot or not operate properly until the overload is removed.
The following table lists the maximum power that each XC5 port can supply:
Port | Max Power |
|---|---|
RJ-45 | 180mA (when transferring data) |
USB-C | 500mA, 900mA, and 1.5A modes |
USB-A | 5V @ 1.5A |
GPIO 3.3V | 3.3V @ 1.0A |
HDMI® (per port) | 5V @ 300mA (protected above 400mA) |
IR blaster output | 3.3V @ 85mA (current-limited with a 39Ω resistor) |
M.2 Wi-Fi module | 3.3V (combined M.2 limit: 3.5A) |
M.2 SSD module | 3.3V (combined M.2 limit: 3.5A) |
PoE Type 1 (XD5 and XT5)
When the player is powered via Type 1 Power over Ethernet (PoE), the total available power is reduced to 12W. This means that each USB port (on models with USB) supplies 100mA of power (one unit load for USB 2.0). This is sufficient for low-power devices such as memory sticks and mice. High-power devices such as hard disks will not operate.