---
title: Series 6 Interfaces
slug: hardware/series-6-interfaces
createdAt: 2026-11-12T22:17:55.771Z
---

This page describes the hardware interfaces on **Series 6&#x20;**&#x70;layers.

# Interfaces by Model

| **Interface**                                   | **HD226** | **HD1026** | **XD236** | **XD1036** |
| ----------------------------------------------- | --------- | ---------- | --------- | ---------- |
| **Ethernet, primary** (RJ45, 10/100/1000)       | ✅         | ✅          | ✅         | ✅          |
| **PoE** on primary Ethernet (Type 2, up to 25W) | —         | —          | ✅         | ✅          |
| **Ethernet, Control port** (RJ45, 10/100)       | ✅         | ✅          | ✅         | ✅          |
| **Power connector** (12V\@3A)                   | ✅         | ✅          | ✅         | ✅          |
| **HDMI output** (HDMI 2.0a)                     | ✅         | ✅          | ✅         | ✅          |
| **GPIO** (12-pin, 8 inputs/outputs)             | ✅         | ✅          | ✅         | ✅          |
| **IR in/out** (3.5mm)                           | ✅         | ✅          | ✅         | ✅          |
| **Serial** (3.5mm RS-232)                       | —         | ✅          | —         | ✅          |
| **Audio** (3.5mm analog/optical combo)          | ✅         | ✅          | ✅         | ✅          |
| **USB-A** (USB 2.0)                             | —         | ✅          | —         | ✅          |
| **USB-C** (USB 2.0)                             | —         | —          | —         | ✅          |
| **microSD, external**                           | ✅         | ✅          | ✅         | ✅          |
| **microSD, internal**                           | ✅         | ✅          | ✅         | ✅          |
| **M.2 Wi-Fi/Bluetooth module** (optional)       | ✅         | ✅          | ✅         | ✅          |
| **M.2 cellular modem** (optional)               | ✅         | ✅          | ✅         | ✅          |
| **Nano-SIM slot**                               | ✅         | ✅          | ✅         | ✅          |
| **M.2 SSD** (optional)                          | —         | —          | ✅         | ✅          |
| **SVC and Reset buttons**                       | ✅         | ✅          | ✅         | ✅          |
| **Status LEDs** (4)                             | ✅         | ✅          | ✅         | ✅          |

**Notes:**

- Only one wireless module can be installed at a time, Wi-Fi or cellular, because both use the same two external antenna connectors.
- The Control Ethernet port is for display control and identification only.

# Interfaces

## Ethernet

**Primary port:** An RJ45 jack supports 10/100/1000 Base-T operation.

*XD models only:* This port also supports Power over Ethernet (PoE). It delivers power on PoE Type 2 and is rated to 25W, provided the upstream Ethernet power feed supports this higher power class.

**Control port:** A second RJ45 jack supports 10/100 Base-T operation and provides a non-PoE network connection. It is intended to create an internal network among a number of screens for screen identification and control. This port is for screen control only (DNS relay is not supported). For examples of how this port can be used, see [Use the Control Port (Examples)](https://docs.brightsign.biz/hardware/YKcw-docs).

- This port is not enabled by default and must be explicitly enabled (which can be done from the BrightSign shell prompt, JavaScript or BrightScript). See [roNetworkConfiguration](https://docs.brightsign.biz/develop/ronetworkconfiguration) or [networkconfiguration](https://docs.brightsign.biz/develop/networkconfiguration) for more information.

802.1x is supported only on the primary Ethernet port. It is not supported on the Control port or on USB-connected Ethernet devices.

## Power Connector

The power connector is rated for 12V @ 3A. When looking directly at the player’s power socket (right-side positive power):

- The ground signal is the pin nearest the edge of the product.
- The 12V power signal is the pin nearest the push buttons.

## HDMI Output

The HDMI® output sends digital video and audio to HDMI-enabled sink devices. It is HDMI 2.0a. CEC control is supported over the HDMI interface.

The players support HDR video as well as:

- 3840x2160x60p 10-bit video decode and display
- Dual 3840x2160x60p 10-bit video decode and playback (XD models only)
- 3840x2160x60p video rotation
- 3840x2160 graphics plane resolution

## GPIO

Players have a 12-pin GPIO switch and LED connector, which allows the player to control external LEDs or other devices requiring 24mA of current or less.

The GPIO port is a standard design manufactured by Phoenix Contact, Wurth Electronics, and others. Pluggable GPIO terminal blocks can be inserted into the GPIO connector to make bare-wire contacts (see here for an example part). These terminal blocks can be purchased from the BrightSign Store. If you wish to source your own terminal blocks, make sure to use 4-pin or 6-pin blocks (12-pin blocks are extremely difficult to remove from the GPIO port).

Connect the LED outputs to the LED ANODE and connect the LED CATHODE to the ground. If you want to connect another device, then the output is capable of sourcing or sinking up to 3.3V at 24mA, but there is a series resistor of 100Ω in each line.

The GPIO also lets you connect external contact closures to ground. In order to connect a switch, connect one side of the switch to the switch input, and connect the other side to one of the ground pins on the GPIO connector. The connector can also supply 3.3V at up to 500mA to an external device. The 3.3V output is polyfuse-protected and can source up to 500mA.

If one BrightSign player is driving the inputs on another BrightSign player, then you can drive at most three inputs from one output. The following calculations explain this limitation:

The GPIO outputs have 100Ω series resistors; the GPIO inputs have 1kΩ pull-up resistors to 3.3V; and the input threshold is 2V high and 0.8V low. The high voltage is not problematic, but the low voltage can be if there are too many inputs connected to one output.

| **Configuration**         | **Calculation**           | **Low-level input voltage** | **Within 0.8V threshold?** |
| ------------------------- | ------------------------- | --------------------------- | -------------------------- |
| 1 output driving 1 input  | 3.3 × 100 / (100 + 1,000) | 0.30V                       | Yes                        |
| 1 output driving 2 inputs | 3.3 × 100 / (100 + 500)   | 0.55V                       | Yes                        |
| 1 output driving 3 inputs | 3.3 × 100 / (100 + 333.3) | 0.76V                       | Yes (max)                  |
| 1 output driving 4 inputs | 3.3 × 100 / (100 + 250)   | 0.94V                       | No                         |

### GPIO Pinout

The following table illustrates the pinout of the GPIO on Series 6 HD and XD players:

| **Pin** | **Function** | **Pin** | **Function** |
| ------- | ------------ | ------- | ------------ |
| 1       | GND          | 7       | GND          |
| 2       | 3.3V         | 8       | 3.3V         |
| 3       | BUTTON 0     | 9       | BUTTON 4     |
| 4       | BUTTON 1     | 10      | BUTTON 5     |
| 5       | BUTTON 2     | 11      | BUTTON 6     |
| 6       | BUTTON 3     | 12      | BUTTON 7     |

The following schematic illustrates the pinout of the GPIO connector.

::Image[]{src="https://api.archbee.com/api/optimize/0prk6SO2dy9LdU77jB8D1/wTI0J00_80Yn6K5Pg1jwe-20251022-215100.png" size="70" width="2307" height="555" position="center" darkWidth="2307" darkHeight="555" showCaption="false"}

## IR Input / Output

The IR blaster generates or receives a space-encoded NEC or Pronto Hex signal. RC5 encoding is also supported. The two transported bit values of the signal (0 and 1) are encoded using differing lengths of low-time IR pulses.

The 3.5mm IR in/out port has the following pinout:

- Tip: 3.3V\@50mA
- Ring: IR Input
- Sleeve: IR Output

:::hint{type="info"}
The sleeve is used as a ground during input operations.
:::

## Serial Input / Output (HD1026 & XD1036 only)

The HD1026 and XD1036 have a UART (asynchronous serial) interface on a 3.5mm (1/8") jack. It uses standard RS-232 signal levels and polarities. The HD226 and XD236 do not support serial I/O.

The default baud rate is 115200, with no parity, 8 data bits, and 1 stop bit. These settings can be configured in software. The interface supports TX, RX, and ground only; RTS/CTS hardware flow control is not supported. The following diagram shows the behavior of the TX and RX signals:

::Image[]{src="https://api.archbee.com/api/optimize/0prk6SO2dy9LdU77jB8D1/HUEwzccc1s_rpI9Wmklyy_serial-tx-rx-signals.png" size="90" isUploading="false" position="center" width="2178" height="692" darkWidth="2178" darkHeight="692" showCaption="false"}

The 3.5mm serial port has the following configuration (from the perspective of the player):

- **Tip**: Receive
- **Ring**: Transmit
- **Sleeve**: Ground

BrightSign players are DTE devices, so communication with another DTE device that uses a 3.5mm port would require a null-modem cable or converter that transposes the TX/RX signals. If the other device uses a DE9 serial port, wire the cable as shown:

![](https://api.archbee.com/api/optimize/0prk6SO2dy9LdU77jB8D1/T1K0T2MIoLNce7FFogMvu_de9-wiring-diagram.png)

## Audio Connector

The players have a combination analog / optical 3.5mm audio jack. **HD226 / HD1026** players also have a dedicated 3.5mm stereo audio port. To transmit a digital audio signal, use a TOSLINK optical audio cable with a 3.5mm connector. Analog and digital audio cannot be transmitted at the same time. Dolby audio is supported as a paid license.

The full-scale voltage output of the analog audio is 2V RMS. The minimum load impedance is 32Ω.

The analog audio connector has the following pinout:

- Tip: Left audio
- Ring: Right audio
- Sleeve: Ground for audio signal

## USB

- **HD1026:** One USB-A port
- **XD1036:** One USB-A port and one USB-C port. The USB-C port supports both device and host mode.
- **HD226 and XD236:** No USB ports

All USB ports meet USB 2.0 specifications and provide 5V @ 1.5A per port to peripheral devices.

## SVC (Service) Button

The SVC button is a recessed button used for various service and recovery tasks. Some functions use the SVC and Reset buttons together (example: [Factory Reset a Player](https://docs.brightsign.biz/hardware/factory-reset-a-player)).

The SVC (Service) button is connected to a dedicated GPIO input as indicated below. Pressing the button pulls the pin low, while releasing the button pulls the pin high.

| **Series 6 Model** | **GPIO Pin** |
| ------------------ | ------------ |
| HD6                | GPIO02       |
| XD6                | GPIO12       |

## Reset Button

The Reset button is a recessed button that restarts the player. A short press results in a soft reset / reboot (orderly OS shutdown). A long press (5–10 seconds, depending on the model) results in a hard reset / reboot (immediate reboot, similar to disconnecting and reconnecting power), which restarts the player even if the software isn’t responding. Neither action changes settings or erases content.

## microSD Slots

The players have two microSD slots, one external and one internal. The internal slot supports speeds up to SDR104, and the external slot supports speeds up to DDR50. There is no built-in limit on the storage capacity of microSD cards used with the player.

## SSD Interface (XD models only)

XD236 and XD1036 players accept NVMe SSDs in M.2 2242 or 2280 form factors (not 2260) with the SX id type (single-sided). Double-sided drives (DX id type)\* will not fit, because the back of the SSD sits essentially flush against the motherboard. For example, a 2280-S1 module will fit, but a 2280-D2 module will not. NVMe drives with heat sinks are not compatible.

\*D4 drives may fit but have not been tested.

## Wi-Fi and Antennas

The players have an E-key M.2 connector that supports 2230 form factor M.2 cards for Wi-Fi (PCIe interface with 802.11n and 802.11ac compatibility) and Bluetooth (USB interface) connectivity.

The [WD105/WD107 Wi-Fi Kit (Series 5 & 6)](https://docs.brightsign.biz/hardware/wd105wd107-wi-fi-kit-series-5-and-6) kit includes a card with two, pre-attached antenna cables (IPEX4 MHF4 type) which connect the module to antenna connectors (IPEX MHF4L type) on the main board. Two adjustable SMA-based antennas can be attached externally.

:::hint{type="info"}
The WD105 and WD107 kits require BrightSignOS 9.1.151.1 or later.&#x20;
:::

## Cellular Modem

The players have a B-key M.2 connector that supports 4230 form factor M.2 cards for cellular modem (USB interface) connectivity. The recommended card is the Quectel EM05-G IoT/M2M-optimized LTE Cat 4 module. The external SMA connectors can be used to mount two 4G/5G antennas suited to the region of intended use. You will need to source two internal cables with suitable connectors to connect the card to the antennas.

A nano-SIM card socket is located on the PCB assembly. Cellular modem cards with components on the rear will not fit.

