---
title: Series 5 Interfaces
slug: hardware/series-5-interfaces
createdAt: 2026-11-13T22:31:06.015Z
---

This page describes the hardware interfaces on **Series 5** players.

# Interfaces by Model

| **Interface**               | **LS425** | **LS445** | **HD225** | **HD1025** | **XD235**    | **XD1035**   | **XT245**    | **XT1145**   | **XT2145**   | **XC2055**           | **XC4055**           |
| --------------------------- | --------- | --------- | --------- | ---------- | ------------ | ------------ | ------------ | ------------ | ------------ | -------------------- | -------------------- |
| Ethernet                    | ✅         | ✅         | ✅         | ✅          | ✅<br />(PoE) | ✅<br />(PoE) | ✅<br />(PoE) | ✅<br />(PoE) | ✅<br />(PoE) | ✅                    | ✅                    |
| HDMI input                  | —         | —         | —         | —          | —            | —            | —            | ✅            | ✅            | —                    | —                    |
| HDMI output                 | 1         | 1         | 1         | 1          | 1            | 1            | 1            | 1            | 2            | 2                    | 4                    |
| GPIO (12-pin)               | Via USB-C | Via USB-C | ✅         | ✅          | ✅            | ✅            | ✅            | ✅            | ✅            | ✅                    | ✅                    |
| IR in/out (3.5mm)           | Via USB-C | Via USB-C | ✅         | ✅          | ✅            | ✅            | ✅            | ✅            | ✅            | ✅                    | ✅                    |
| Serial (3.5mm)              | Via USB-C | Via USB-C |           | ✅          |              | ✅            |              | ✅            | ✅            | ✅                    | ✅                    |
| Audio (analog/optical)      | ✅         | ✅         | ✅         | ✅          | ✅            | ✅            | ✅            | ✅            | ✅            | ✅<br />(analog only) | ✅<br />(analog only) |
| USB-A                       | —         | —         | —         | 1 (2.0)    | —            | 1 (2.0)      | —            | 1 (2.0)      | 1 (2.0)      | 1 (3.0)              | 1 (3.0)              |
| USB-C                       | 1 (3.0)   | 1 (3.0)   | —         | —          | —            | 1            | —            | 1            | 1            | 1 (3.0)              | 1 (3.0)              |
| M.2 Wi-Fi / BT slot + 2 SMA | ✅         | ✅         | ✅         | ✅          | ✅            | ✅            | ✅            | ✅            | ✅            | ✅                    | ✅                    |
| M.2 NVMe SSD                | —         | —         | —         | —          | ✅            | ✅            | ✅            | ✅            | ✅            | ✅                    | ✅                    |

# Interfaces

## Ethernet / PoE

The Ethernet connection (RJ45) is used to connect an Ethernet cable for network access. Some players also have Power over Ethernet (PoE) capabilities.

| **Player Family** | **Speed**        | **PoE**                                                |
| ----------------- | ---------------- | ------------------------------------------------------ |
| LS5               | 10/100 Mbps      | Not supported                                          |
| HD5               | 10/100/1000 Mbps | Not supported                                          |
| XD5               | 10/100/1000 Mbps | PoE Type 1 up to 12.95W, PoE Type 2 (PoE+) up to 25.5W |
| XT5               | 10/100/1000 Mbps | PoE+ supported                                         |
| XC5               | 10/100/1000 Mbps | Not supported                                          |

The maximum length for Cat 5E cable is 100 meters; the allowed length can be higher or lower depending on the quality of the cable.

802.1x is supported on the Ethernet port, but not on USB-connected Ethernet devices.

## Power Connector

The power connector connects the power cord to the device.

| **Players**   | **Rating** | **Connector**                                                                                           |
| ------------- | ---------- | ------------------------------------------------------------------------------------------------------- |
| LS5           | 12V @ 1.5A | Power input only; it does not transfer data.                                                            |
| HD5, XD5, XT5 | 12V @ 3A   | Locking connector to prevent inadvertent disconnections. XD5: right-side positive, locking 2-pin (1x2). |
| XC5           | 19V @ 4.7A | Locking connector to prevent inadvertent disconnections.                                                |

## HDMI Input (XT1145, XT2145 only)

The HDMI®-in connector is used to receive digital video and audio from HDMI-enabled source devices. It can accept a maximum video resolution of 4096x2160x60p. HDMI input is not available on the XT245.

The HDMI signaling has CEC functionality. The CEC channel is electrically coupled to the corresponding signal on the HDMI output, and CEC commands pass through the player even when it does not have power.

## HDMI Output

The HDMI®-out connector is used to send digital video and audio to HDMI-enabled sink devices. CEC control and AVI are supported over each HDMI interface independently. On players with more than one output, the player can maintain the configured multiscreen layout if one of the HDMI outputs loses sync.

| **Players**       | **Outputs** | **HDMI version**                               | **Maximum resolution / decode**                                                                                        |
| ----------------- | ----------- | ---------------------------------------------- | ---------------------------------------------------------------------------------------------------------------------- |
| LS425             | 1           | HDMI 2.0a                                      | Full HD, up to 2048x1048x60p                                                                                           |
| LS445             | 1           | HDMI 2.0a                                      | UHD/4K, up to 3840x2160x60p                                                                                            |
| HD225<br />HD1025 | 1           | HDMI 2.0a                                      | At least two simultaneous 1920x1080x60p decodes                                                                        |
| XD235<br />XD1035 | 1           | HDMI 2.0a                                      | 3840x2160x60p; HDR; video rotation at 2160x3840x60p; at least two simultaneous 1920x1080x60p decodes                   |
| XT245<br />XT1145 | 1           | HDMI 2.1a                                      | 7680x4320x60p; HDR; dual 4K decode                                                                                     |
| XT2145            | 2           | HDMI-1: HDMI 2.1a;<br />HDMI-2: HDMI 2.0a      | 7680x4320x60p; HDR; dual 4K decode                                                                                     |
| XC2055            | 2           | HDMI-1: HDMI 2.1a;<br />HDMI-2: HDMI 2.0a      | 7680x4320x60p (8-bit decode); HDR10, HLG; rotation at 2160x3840x60p; at least four simultaneous 3840x2160x60p decodes  |
| XC4055            | 4           | HDMI-1: HDMI 2.1a;<br />HDMI-2 to 4: HDMI 2.0a | 7680x4320x60p (10-bit decode); HDR10, HLG; rotation at 2160x3840x60p; at least four simultaneous 3840x2160x60p decodes |

## GPIO

HD5, XD5, XT5, and XC5 players have a 12-pin GPIO switch and LED connector, which allows the player to control external LEDs or other devices requiring 24mA of current or less. Each button pin can sink or source 24mA. LS5 players support GPIO through a USB-C to GPIO cable (see USB).

| **Model** | **3.3V supply (PWR pins)**        | **Aux power** |
| --------- | --------------------------------- | ------------- |
| HD5       | 3.3V @ 500mA (polyfuse-protected) | —             |
| XD5       | 3.3V @ 300mA                      | 1A            |
| XT5       | 3.3V @ 500mA                      | 1A            |
| XC5       | 3.3V @ 300mA (Rev G and later)    | 1A            |

The GPIO port is a standard design manufactured by Phoenix Contact, Wurth Electronics, and others. Pluggable GPIO terminal blocks can be inserted into the GPIO connector to make bare-wire contacts (see here for an example part). These terminal blocks can be purchased from the BrightSign Store. If you wish to source your own terminal blocks, make sure to use 4-pin or 6-pin blocks (12-pin blocks are extremely difficult to remove from the GPIO port).

Connect the LED outputs to the LED ANODE and connect the LED CATHODE to the ground. If you want to connect another device, the output is capable of sourcing or sinking up to 3.3V at 24mA, but there is a series resistor of 100Ω in each line.

The GPIO also lets you connect external contact closures to ground. To connect a switch, connect one side of the switch to the switch input, and connect the other side to one of the ground pins on the GPIO connector.

If one BrightSign player is driving the inputs on another BrightSign player, you can drive at most three inputs from one output. The following calculations explain this limitation:

The GPIO outputs have 100Ω series resistors; the GPIO inputs have 1kΩ pull-up resistors to 3.3V; and the input threshold is 2V high and 0.8V low. The high voltage is not problematic, but the low voltage can be if there are too many inputs connected to one output.

| **Configuration**         | **Calculation**           | **Low-level input voltage** | **Within 0.8V threshold?** |
| ------------------------- | ------------------------- | --------------------------- | -------------------------- |
| 1 output driving 1 input  | 3.3 × 100 / (100 + 1,000) | 0.30V                       | Yes                        |
| 1 output driving 2 inputs | 3.3 × 100 / (100 + 500)   | 0.55V                       | Yes                        |
| 1 output driving 3 inputs | 3.3 × 100 / (100 + 333.3) | 0.76V                       | Yes (max)                  |
| 1 output driving 4 inputs | 3.3 × 100 / (100 + 250)   | 0.94V                       | No                         |

### GPIO Pinout

The following table illustrates the pinout of the GPIO on HD5, XD5, XT5, and XC5 players:

| **Pin** | **Function** | **Pin** | **Function** |
| ------- | ------------ | ------- | ------------ |
| 1       | GND          | 7       | GND          |
| 2       | 3.3V         | 8       | 3.3V         |
| 3       | BUTTON 0     | 9       | BUTTON 4     |
| 4       | BUTTON 1     | 10      | BUTTON 5     |
| 5       | BUTTON 2     | 11      | BUTTON 6     |
| 6       | BUTTON 3     | 12      | BUTTON 7     |

The following schematic illustrates the pinout of the GPIO connector:

![](https://api.archbee.com/api/optimize/Aiw58-3NpdDpGlgjiVvLS-sY7nDwWhBxFNEJnmJQUkB-20250530-214854.png)

### XC5 Pin Functions

On XC5 players, some GPIO pins also have secondary functions:

| **Pin** | **Primary** | **Secondary** | **Tertiary** |
| ------- | ----------- | ------------- | ------------ |
| 3       | Button0     | UART1\_RXD    |              |
| 4       | Button1     | IR\_IN        |              |
| 5       | Button2     | SPDIF1\_OUT   |              |
| 6       | Button3     | PWM           |              |
| 9       | Button4     | UART0\_RXD    | I2C\_SCL     |
| 10      | Button5     | UART0\_TXD    | I2C\_SDA     |
| 11      | Button6     | UART1\_TXD    |              |
| 12      | Button7     | IR\_OUT       |              |

## IR Input / Output

HD5, XD5, XT5, and XC5 players have a 3.5mm IR in/out port. On LS5 players, IR in/out is provided via USB-C (see USB).

The IR blaster can transmit and receive a variety of common Consumer-IR formats including NEC and RC5. The two transported bit values of the signal (0 and 1) are encoded using differing lengths of low-time IR pulses.

The 3.5mm IR in/out port has the following pinout:

- Tip: 3V\@50mA
- Ring: IR Input
- Sleeve: IR Output/GND

For IR transmit:

- Tip: 3V\@50mA
- Ring: Not used
- Sleeve: IR Output

For IR receive:

- Tip: 3V\@50mA
- Ring: IR Input
- Sleeve: GND

## Serial

The HD1025, XD1035, XT1145, XT2145, XC2055, and XC4055 have a UART (asynchronous serial) interface in a 3.5mm (1/8") jack that connects a serial modem or other devices that use a serial connector. The HD225, XD235, and XT245 do not have a serial port. LS5 players support serial through a USB-C to USB-A and 3.5mm serial cable (see [Series 5 Interfaces](https://docs.brightsign.biz/hardware/series-5-interfaces#x5mJd)).

The serial port uses standard RS-232 signal levels and polarities.

The default baud rate of the interface is 115200, with no parity, 8 data bits, and 1 stop bit. These settings can be configured in the software. The serial interface supports TX, RX, and ground only—RTS/CTS hardware flow control is not supported. The following diagram illustrates the behavior of the TX and RX signal:

::Image[]{src="https://api.archbee.com/api/optimize/0prk6SO2dy9LdU77jB8D1/HUEwzccc1s_rpI9Wmklyy_serial-tx-rx-signals.png" size="90" isUploading="false" position="center" width="2178" height="692" darkWidth="2178" darkHeight="692" showCaption="false"}

This 3.5mm serial port has the following configuration (from the perspective of the player):

- Tip: Receive
- Ring: Transmit
- Sleeve: Ground

BrightSign players are DTE devices, so communication with another DTE device that uses a 3.5mm port would require a null-modem cable or converter that transposes the TX/RX signals. If the device communicating with the player uses a DE9 (also known as DB9) serial port, such as a PC, the serial cable should be wired as shown in the following diagram:

![](https://api.archbee.com/api/optimize/0prk6SO2dy9LdU77jB8D1/T1K0T2MIoLNce7FFogMvu_de9-wiring-diagram.png)

For detailed Serial Adaptor instructions see this PDF:

::File{src="https://api.archbee.com/api/presign/Aiw58-3NpdDpGlgjiVvLS-38MXQCbkbYrwgYZ6jWmqe-20250714-224638.pdf" label="BrightSign Serial Adaptor Instructions_female.pdf"}

## Audio Connector

LS5, HD5, XD5, and XT5 players have a 3.5mm combination analog/optical audio jack. XC5 players have a 3.5mm analog-only audio jack (no optical output). The HD225 and HD1025 also have a dedicated 3.5mm stereo audio port.

To transmit a digital audio signal, use a TOSLINK optical audio cable with a 3.5mm connector. Analog and digital audio cannot be transmitted simultaneously.

- XT5: The player supports passthrough of EAC3 and AC3 over valid outputs (TOSLINK supports AC3 only, not EAC3).
- HD5: Dolby audio is supported as a paid license.

The full-scale voltage output of the analog audio is 2V RMS. The minimum load impedance is 32Ω.

The analog audio connector has the following pinout:

- Tip: Left audio
- Ring: Right audio
- Sleeve: Ground for audio signal

## USB

| **Players**            | **USB ports**                                                |
| ---------------------- | ------------------------------------------------------------ |
| LS425, LS445           | One USB-C 3.0 port                                           |
| HD225, XD235, XT245    | None                                                         |
| HD1025                 | One USB-A 2.0 port (provides 5V @ 1A for peripheral devices) |
| XD1035, XT1145, XT2145 | One USB-A 2.0 port and one USB-C 2.0 port                    |
| XC2055, XC4055         | One USB-A 3.0 port and one USB-C 3.0 port (5V @ 1A per port) |

The USB-C port supports both device and host mode, as well as BrightSign USB accessories. On LS5 players, the USB-C port supports custom cable solutions such as USB-C to GPIO, USB-C to USB-A and 3.5mm serial, and USB-C to IR.

## SVC (Service) Button

The SVC button is a recessed button used for various service and recovery tasks. Some functions use the SVC and Reset buttons together (example: [Factory Reset a Player](https://docs.brightsign.biz/hardware/factory-reset-a-player)).

The SVC (Service) button is connected to a dedicated GPIO input as indicated below. Pressing the button pulls the pin low, while releasing the button pulls the pin high.

| **Series 5 Model** | **GPIO Pin** |
| ------------------ | ------------ |
| LS5                | GPIO02       |
| HD5                | GPIO02       |
| XD5                | GPIO12       |
| XT5                | GPIO02       |
| XC5                | GPP\_D5      |

## Reset Button

The Reset button is a recessed button that restarts the player. A short press results in a soft reset / reboot (orderly OS shutdown). A long press (5–10 seconds, depending on the model) results in a hard reset / reboot (immediate reboot, similar to disconnecting and reconnecting power), which restarts the player even if the software isn’t responding. Neither action changes settings or erases content.

## microSD Slot

All Series 5 players have one microSD slot, which supports transfer modes up to UHS-I DDR50 (50MB/s) on LS5, HD5, XD5, and XT5 players, and up to UHS-I SDR104 on XC5 players. There is a 2TB limit on the storage capacity of microSD cards used with the player.

## SSD Interface (XD5, XT5, and XC5 only)

XD5, XT5, and XC5 players accept NVMe SSDs in M.2 2242 or 2280 (but not 2260) form factors of SX id type (single-sided form factor). Double-sided drives (DX id type) will not fit because the back side of the SSD may interfere with the motherboard (D4 drives *may* fit but have not been tested). For example, a 2280-S1 module will fit a BrightSign player but a 2280-D2 module would not.

NVMe drives with heat sinks are not compatible with BrightSign players. On XC5 players, the SSD interface is NVMe over PCIe 3.0 x4.

## Wi-Fi and Antennas

All Series 5 players have an M.2 connector that supports M.2 cards for Wi-Fi (PCIe interface with 802.11n and 802.11ac compatibility) and Bluetooth (USB interface) connectivity.

The [WD105/WD107 Wi-Fi Kit (Series 5 & 6)](https://docs.brightsign.biz/hardware/wd105wd107-wi-fi-kit-series-5-and-6) kit includes a card with two, pre-attached antenna cables (IPEX4 MHF4 type) which connect the module to antenna connectors (IPEX MHF4L type) on the main board. Two adjustable SMA-based antennas can be attached externally.

:::hint{type="info"}
The WD105 and WD107 kits require BrightSignOS 9.1.151.1 or later.&#x20;
:::

